Advances in Building Stairs / Staircases / Deck Stairs Provide Superior Structural Integrity and Safety.

Let’s walk through the most important issues that have ‘tainted’ the decking industry and quickly highlight the major improvements that have provided new economical and efficient solutions that have effectively addressed the ‘trouble’ spots.

With the rapid increase in new material options such as composite material there have been excellent improvements in long lasting ‘color stabilization. When many of the composite manufacture’s first came on the scene they lacked sufficient UV (Ultra Violet) stabilizers in the custom color coatings they applied. Terrific new color options became available to builders, however, significant premature ‘fading’ was seen and customer complaints were common. Now, unlike the first generation of composite, new advanced UV color coating provides long lasting color consistency. In addition to the early problems of inadequate UV stabilizers, the initial cost was hard for many installers to swallow too! Now that the market place has encouraged more competition-the price of composite has come down and has become a very affordable, long lasting option versus traditional redwood, cedar and pressure treated lumber.

The whole topic of pressure treated lumber has also been an extremely controversial issue during this last decade. When the EPA (Environmental Protection Agency) banned the use of arsenic and changed the main pressure treatment to ‘copper they failed to realize the major implications that would arise. Arsenic was eliminated due to the potential harm it exposed children to on playgrounds all across the nation. The new pressure treated solution now approved by the EPA and presently being used contains a high level of copper.

This relatively new approved pressure treatment when it comes in contact with galvanized-zinc coated steel accelerates corrosion at a rapid level. This set the stage for a dramatically different safety concern – with the earlier Arsenic pressure treatment the danger was possible poisonous ‘ingestion’¬¬ – now with the new, high copper content pressure treatment, widespread deck collapses and premature corrosion are the real safety concerns. Scrambling to quickly respond to the potential safety and liability concerns, manufacturers of steel hangers, fasteners (screws/nails etc.) immediately improved their products by adding hot-dipped galvanization to all anchors, hangers and fasteners and in many cases, adding epoxy powder coatings in addition to increasing the levels of hot-dipped galvanization. This so far, as been ‘perceived’ as an adequate solution. However, galvanic corrosion created between the high copper content of the wood and the galvanizing has shown to be so severe that the normal industry standard of G90 galvanizing will corrode in as little as 12 months and G185 can be seriously compromised with 24 months. Surprisingly, the G185 with no engineering testing available, has been the industry default for code officials. Without a barrier between the pressure treated wood and galvanized hardware, serious corrosion is inevitable. More work still needs to be done in safely addressing this EPA approved pressure treatment.

Standard, traditional deck installation and construction as a whole has come under great scrutiny within the last decade too. Many structural solutions have been advanced to improve deck attachments and stability. Highly publicized deck collapses have focused a spot light on safety issues but have missed the target on the major cause of fatalities and injuries. Deaths resulting from deck collapses although tragic are less than 40 per year across the US. However, statistics provided by the National Safety Council show fatalities on stairs approaching 2,000 per year- which do not include the serious injuries that have additionally occurred. (National Safety Council Injury Facts 2011 Edition).
The above injuries are a result of slips and falls on the most dangerous area of any deck or home: stairs (deck stairs, wood stairs, exterior stairs, interior stairs). Substandard construction practices have led to unstable railing and the inability to provide adequate grip as a person traverses a stairway. For years building codes have existed requiring rail posts to withstand 200lbs. of lateral load. Until just recently, there have been no solutions which allow standard wood stair construction to meet these criteria. Traditional poor construction methods are a direct cause that has led to these above statistics.

There have been just a handful of manufacturer’s that have made serious efforts at addressing various lateral load deck safety concerns for safer stair railings. One of these manufacturer’s, EZ Stairs,Inc. makes an adjustable bracket that can also be used as a vertical deck stair rail post attachment for deck stairs. Also read how ICC-ES has recognized EZ Stair’s stair rail solution.
ESRecognizesInnovativeSolutions_StairRailSafetyConcerns.pdf

Unfortunately, until such time as adequate code enforcement is required the above unnecessary fatalities and injuries will continue and many feel given the large number of reported injuries, it is grossly negligent for Building Inspectors not to require tested and validated products. The ICC-ES does an adequate job of informing the code official community of code tested solutions but they are largely ignored and sadly expose the general public to hazards that are unnecessary.

EZ Stairs Inc. is not only a easy to install two stringer stair system for risers and treads, but also functions as a vertical rail post attachment (rail safety bracket) that exceeds current code by 2.5x giving you safe, reliable stairs. Build exterior deck stairs up to 7′ wide or 9′ wide interior stairs with only 2 stringers- saving labor and materials. Since the riser acts as a load bearing joist, you get an incredibly strong stair that doesn’t squeak. With the patented adjustable dual-purpose exterior/interior brackets EZ Stairs won Pro Sales Magazine’s Editor’s Choice award for new product innovation in the construction industry. In 2005, it introduced its composite deck compatibility solution and was chosen for LBM Journal’s ‘Hot Products’ Award at the International Builders Show, and again voted one of the fifty ‘Hot Products’ at more recent International Builders Shows. EZ Stairs is code approved and recognized by the ICC-ESR 2295.
For more information, and to view 3D demos, visit the ez-stair.com website, or call 866-693-9570.

Building Easy to Install Basement Stairs on a Budget.

Basement stairs come in all shapes and sizes from the very simple utility/access stair to the more elaborate decorative stairs where the basement is expanded to be a major part of the living area. One of the major issues facing the stair builder is the unpredictable overall stair height that often occurs with basement stairs. Whether new or existing construction, the basement slab height nearly always seems to vary up or down making pre-built stairs problematic. For this reason basement stairs are usually built to customized heights.

The normal procedure in the industry is to call out a stair specialist to custom build the stair using 2×12 cut stringers as framing for constructing the stair. This can be a difficult and costly process, requiring a high degree of skill. However, there is an easier solution available that will save you time as well as money. The system consists of self adjusting stair brackets, used to form an ”engineered stair”. Adjustable stair brackets are a custom tailored approach to stair building that are much faster, easier and stronger than conventional construction. They’re a handy, low cost solution for the unpredictable slab height problem.

This bracket system can quickly form a basic utility stair or an elaborate, fully finished hardwood stair. The adjustable brackets basically do the work for you, making the whole stair building process simple and streamlined. The brackets are approved as adjustable joist hangers which allow the risers to be structurally attached to the stringers, carrying the load across the stair like stepping floor joists. This greatly enhances the strength of the stair and permits the stair to be built using only two stringers. The stringers themselves are full depth unlike cut stringers and are again engineered to carry much greater loads than conventional cut stringers. Only three to four end cuts are required per stringer which eliminates approximately seventy saw cuts when compared to conventional cut stringers for basement stairs.

A wide range of materials such as pine, MDF treads, hardwoods etc. can be used. Adjustable brackets allow for customized rise and tread configurations which can be adjusted to meet all building codes for any interior or exterior application.

This is how it works: Set the brackets on the two 2×6 stringer members using the spacers and pivot screws. Remove spacers and rotate brackets to adjust stair height. Fix brackets in position, attach risers and treads. See 3D demos and photos online and view the simplicity for yourself.

Before you begin, determine the material you are going to use, the exact number of steps you need and the stair width.

You will need (2) 2×6’s per stringer for each side. Make sure when you purchase your 2×6’s make sure that they are straight without any twist. The 2×6’s will need to be at least 12″ longer than the total length of your stairs. Two stringers are sufficient to span up to 9’ in stair width due to the extraordinary strength developed by this engineered system.

For risers you will use 2×8’s for riser heights up to 7-1/4” and 2×10’s for higher risers. For treads you can use 2×12’s, 5/4 pine or MDF, 5/4 hardwood, sturdy floor ripped to size etc.. Time saving tip: when you determine how many steps you will need and your stair width….get all your risers and treads pre-cut to exact lengths when you purchase the materials.

Tools/Materials needed will be: a power drill, saw (skill saw is preferable, but not required, #8 1 1/4″ Phillips flat head or star/square drive screws for the stair brackets, #8 2 1/2″ deck screws for every 9″ of tread and riser connection and EZ Stair Spacers for customized riser and tread measurements.

Being ICC approved, the “Engineered Stair System” eliminates the need to cut stringers and is tested to be much stronger and faster than conventional construction. In fact, you can save at least $500 per flight of stairs with adjustable brackets over traditional construction methods. Whether you’re a seasoned professional or a do-it-yourselfer, you will build fast, strong and accurate stairs, on a budget with this method.

EZ Stairs® introduced the new patented adjustable dual-purpose exterior/interior brackets in 2003. In 2004, it won Pro Sales Magazine’s Editor’s Choice award for new product innovation in the construction industry. In 2005, the company introduced its composite deck compatibility solution for and was chosen for LBM Journal’s ‘Hot Products’ Award at the 2005 International Builders Show, and again voted one of the fifty ‘Hot Products’ at the 2008 International Builders Show. Big builders, as well as the DIY market are using EZ Stairs for interior stairs such as

Being an adjustable bracket building system allows for easy to install, customized rise and treads configurations, which can be adjusted to meet all building codes for any interior or exterior application- ICC approved. EZ Stairs is the only adjustable stair bracket system available anywhere. To help you figure out how many stairs you will need, the website provides a free stair calculator.

Deck Stairs Made Easy.

Deck Stairs are often the last part of the deck to be tackled because they are often the most difficult part of the deck to build. I’ve found a solution for building deck stairs that’s stronger, faster and easier than any system of stair building I’ve ever seen. I’ve built many decks in my early days as a professional. Building stairs was always something I had to tackle myself because I couldn’t trust anyone else to build the stairs correctly… the first time.

I’m referring to an adjustable, heavy duty steel stair bracket system, which allows you to make automatic adjustments to form any rise or run you require. You only need two stringers for deck stairs up to 7’ in width. No center stringers are needed at all because riser acts as a load-bearing joist, giving you strong stairs. Most of the saw cuts are eliminated and require only three to four cuts per stringer.

These EZ Stairs® brackets not only adjust, but are also approved as ‘joist hangers’. This allows you to attach 2” thick risers that span across the stair like floor joists, every 10” or 11” between the two stringers. This eliminates the need for several center stringers running down the stair as in conventional construction. Since there are only two stringers, you also eliminate the need to align and attach several cut stringers in order to build your stair.

The brackets also provide ‘code compliant’ rail post support. According to their accredited testing, the brackets are used to provide rail post support for any type of wood stair which meets the code requirement for 200lb. Lateral load at 42”. This has never been achieved on any wood stairs system.

This stair building system is much simpler and faster than conventional stair building, without sacrificing structural integrity or strength. The stairs turn out so well made that you won’t even hear a squeak. In addition to deck stairs, they can be used for interior stairs: basement stairs, tongue and groove stairs, and even concrete formwork. Check out http://www.ez-stairs.com

Instructions from the website:
Set the brackets on the two 2×6 stringer members using the spacers and pivot screws. Remove spacers and rotate brackets to adjust stair height. Fix brackets in position, attach risers and treads.

Before you begin, determine the exact number of steps you need and exactly how wide you would like your steps to span. If you need additional assistance in obtaining the appropriate measurements-you can quickly link on our brochure ‘Let’s Get Started’ section (available in English and Spanish)* and the free stair calculator at http://www.ez-stairs.com/widgets/stair_calculator/index.html

You will only need (2) 2×6’s per stringer/side*. Make sure when you purchase your 2×6’s that you get them as straight as possible. The 2×6’s will need to be at least 12″ longer than the total length of your stairs. Two stringers are sufficient to span up to 7′ wide. You will only need to make a maximum of 3 to 4 cuts per stringer no matter how many steps you will be building.

For risers you will use 2×8’s — for treads you can use 2×12’s. Utilizing additional EZ Stairs mini-composite cleat brackets you may use any 2×6 tread material wood/and or composite. Time saving tip: when you determine how many steps you will need and how wide you want to span…get all your risers and treads pre-cut to exact lengths before you begin.

For interior jobs you can use same as above or the following can be used for spans up to 42″ to 48″ wide. Stringers still need to be 2×6’s. Interior risers can be 2×8’s or 3/4″ to
1 1/8” plywood. Interior treads can be 2×12’s or 1 1/8″ to 3/4″ plywood with EZ Stairs, stairs can be ‘pre-built’ or built ‘in-place’.

Tools/Materials needed will be: a power drill, saw (skill saw is preferable, but not required, #8 1 1/4″ Phillips flat head or star/square drive screws for the stair brackets, #8 2 1/2″ deck screws for every 9″ of tread and riser connection and EZ Stair Spacers for customized riser and tread measurements.

Watch 3D animation first at www.ez-stairs.com

Set-up (1) stringer at a time by placing 2×6’s parallel on a flat surface…start 6″ from end by placing EZ Stairs spacer, then bracket and spacer…..down the line. When you have all your spacers and brackets lined up and tight insert 2 pivot screws in each bracket… without tightening the pivot screws. Remove spacers and pivot your brackets to your exact riser and tread combination. Insert remaining screws in all the brackets except the first and last step… these brackets will need to be quickly pivoted out of the way to make the required minimal end cuts. Repeat the process on stringer #2 and install all risers and treads.

* Interior or exterior stairs can be framed out and installed in most cases 2-3 hours or less.
* Minimal skill is required and due to the fact that with EZ Stairs saw-cuts are drastically reduced…..material is seldom wasted.
* Spacers are adjustable to allow for customized rise and tread configurations. Spacers are factory set at ‘G’… accomplishes most tread and rise requirements.

Deck Stair Safety- Build Strong & Safe Deck Stairs

Poor Deck and Stair Construction Can Kill

In a recent article published in The Los Angeles Times, July 6th. of this year, a tragic deck collapse resulting in serious injury and death, is reported. The deck was part of a three story apartment complex in a Birmingham suburb. Seven party-goers is all it took to create this tragic event. Unfortunately, this is an all to common occurrence now days. Reports are continually surfacing, confirming the growing frequency of these serious, life threatening collapses.

collapsed deck and stairs

Over the past several years, much has been done to address deck and stair safety issues, but we still have a long way to go. One glaring example of the failure in deck and stair safety protocol is the industry standard of permitting “hot dipped galvanized” anchors, screws, hangers and other hardware to be in direct contact with ACQ, pressure treated wood. The galvanic corrosion created between the high copper content of the wood and the galvanizing is so severe that the normal industry standard of  G90 galvanizing will corrode in as little as 12 months and G185, such as Z-Max® can be gone in 24 months. The industry (including code officials) has adopted G185 as a fall back position with no engineering testing available to substantiate the validity or longevity of this adoption…..this is a “knee jerk” reaction and is an accident waiting to happen. Without a barrier between the pressure treated wood and galvanized hardware, serious corrosion is inevitable.

Take for example the recent NADRA (North American Deck and Railing Association) study that examined the number of injuries caused by outdoor decks and porches from 2003 to 2007. The report states that 224,000 people were injured nationally due to a deck or porch over the study period. Nearly 15 percent of these injuries were a result of a structural failure or collapse. The report concluded that of the 224,00 injuries, 33,000 were a result of a structural failure or collapse. The estimate for “serious” injuries resulting from those failures exceeds 18,000. Serious injuries included head trauma, concussion, major fractures, such as those associated with the back, and paralysis. Wood decks are constantly exposed to the elements and they have a limited life span of 10-15 years. It’s important to have your deck and deck stairs inspected so that signs of wood decay and deterioration can be repaired.

Other codes address “rail post support” safety. A rail post per code regulations is required to support a lateral load of 200 lbs. This is a poorly enforced area of the code and with many inspectors content with the bump test. If it doesn’t move too much when they bump it with their hip, the rail will pass inspection. Many rail posts are simply lagged or nailed to the rim joists and post which are mounted directly to the deck surface will simply not meet code. The tragedy is, there are systems available on the market that correctly address this problem. Simpson, USP and Deck-Loc have brackets which will meet code for rim joist attachment and EZ Stairs has the ONLY system available which will meet code for wood or composite stairs.

Attention is now being given to the ability of the vertical post’s strength when hit by various degrees of lateral thrust pressure.  These new directives, requiring the vertical rail post to support a minimum of 200 lbs. of lateral thrust, is making engineered stair systems such as EZ Stairs extremely popular, especially with this stair system’s ability to withstand over 500 lbs of lateral thrust for the ‘rail post support’ structural sections of the overall decking plans.

Stairs are perhaps the most overlooked area of construction. Stairs using standard cut stringers have been used for eons and are “grandfathered” into code as accepted construction. Stringers are cut from 2×12’s and greatly weakened in the process. Several stringers are then run longitudinal down length of the stair to make up for the strength loss during cutting. Long stair run tend to bounce and stringer failure is not uncommon. Additionally, many of these stairs are built without risers which is a “child safety” issue in many states. General Contractor and renowned professional deck builder, Pat Noonan of Minnesota says, “Of the 50+ decks I have torn off and replaced, not one had a stair system that outlasted the deck.”  The majority of them had shaky, unsafe stairs, and it was the main reason they were doing the rest of the deck.”

Engineered stair systems such as EZ Stairs overcome many of these problems and safety issues. This is due to the much more rigorous testing required to gain ICC/ES acceptance for a stair system which has not been simply “grand fathered” into common use. This adjustable bracket system is engineered in a completely different manner to conventional stair construction. These adjustable steel brackets lock the risers and treads onto the stringers, with a solid, joist hanger type connection. Only two stringers are required for stairs up to 7′ in width. This becomes possible because the two outside stringers are full depth, acting like beams running down the length of the stair ( only three end are cuts required per stringer). Next, the risers (which are locked to the steel brackets) span across the stair like joist hangers, at each step supporting the tread.

The result is a “rock solid” stair which has been tested at over 1,200 lbs. per sq. ft.(uniform distributed load), well in excess of the code requirement of only 100 lbs.per sq. ft. (commercial load). The  steel brackets adjust to form any rise or run required and are powder coated over a hot dipped galvanized finish. The powder coating (paint) sets up an effective barrier between the pressure treated wood and the galvanized finish, preventing corrosion. Additionally the structural risers overcome the child safety issue (found on stairs without risers) and as mentioned above, the brackets have been tested to exceed code requirements for lateral load applied to “rail post” supports.

General Contractor Pat Noonan continues, “Craftsmanship will only take you so far when you are dealing with a inferior framing system and components. When deck builders notch steps out of a 2”x12”, they are cutting all the strength out of the wood and putting the entire weight of the stair plus anyone walking up or down on 4” of wood left in the 2”x12”. With the EZ Stairs system, they are putting the weight on 11’ of solid wood- there’s no comparison”.

Strong, solid stairs with professional craftsmanship using EZ Stairs

For more information, visit the EZ Stairs® website, or call 866-693-9570.

Improved solution to building safer stair railings.

Current IBC® and IRC® codes require guard rails to withstand a lateral load of 200 pounds, applied 36 inches above the nose of the stringer. This isn’t adequate protection for your stair railings or you. Imagine having a group of people on your deck stairs and someone trips and falls against the railing. Imagine if it were a large adult. Imagine if those were aging deck stairs prone to structural weakness anyway.

A newly redesigned adjustable stair bracket provides an innovative solution to this  stair rail  safety concern. It was designed specifically for stair construction and code compliant rail post support. The standard stair bracket was modified and tested for lateral load stair rail post support for cut stringers, angle stringers and for other applications. In more than twelve individual tests, all brackets withstood a load of 500 pounds applied 42 inches above the nose of the tread (an IBC requirement for non-residential applications), with some tests approaching 600 pounds before failure.

The National Safety Council shows slips and falls on stairs, result in 2,000 fatalities each year, making stairs the most dangerous area of the home. Once the hand grip or hand rail becomes unstable, safety is greatly compromised. This is particularly evident with persons over age 65. NSC statistics show that the leading cause of death and serious injuries for persons over age 65 are slips and falls.”

Secure hand and guardrails are critical for stair safety and there are many viable solutions for securing handrails. Unfortunately, this is not always the case for guardrails, specifically when they are attached to wood stairs. Guardrails are normally secured to rail post supports, which in turn are attached to a stringer. Some within the building industry have expressed concern that the standard installation methods used for rail post attachment fall short of meeting the lateral load capacity required by code. Products, such as the bracket evaluated in ICC-ES’s report for code officials and professionals in the construction industry: ESR-2295, helps ensure that current and future construction meets this requirement.

How do most code officials tend to test stair rail safety? Far too often, it’s a ‘tug and bump-the-rail’ test and if it seems solid, it passes. In some traditional construction, stairs are built with three or more cut stringers. Stairs may have both risers and treads, or treads only. The guardrail is normally 36 inches high for residential construction and is secured via posts bolted to the cut stringers. Often, the rails themselves are strong enough to meet code, but the attachment of the post to the stringer is the weak link.

An IAS accredited testing facility was engaged to test the load capacity of this traditional construction practice. A stair was constructed, with three 2×12 cut stringers and two 2×6 members for each tread, using dry, #2 Douglas Fir. Three 48-inch-long posts were attached using two 3/8-inch galvanized bolts. The top bolt was attached through the triangular cut portion of the stringer (normal practice) and the bottom bolt passed through the uncut portion of the stringer. A 3/8-inch eye bolt was attached 36 inches above the nose of the tread as the load point. The load was applied to each post and measured using a dynamometer. In each case, the bolt pulled through the cut, triangular rise/tread tip of the stringer at a load of just 20 pounds. As the load was increased to 50 pounds, severe longitudinal cracks were seen along the length of the stringers, breaking all triangular tips and resulting in complete failure of both the stringer and the rail post support.

All three tests consistently showed significant structural failure occurring at minimal loads and several reasons for the early failure were identified. The post acted as a lever against the stringer, magnifying the load on each bolt. A 20-pound pull at the guardrail level resulted in a 120-pound force at the base of the post and caused the top bolt to pull through the stringer. Once the top bolt had broken through, the bottom bolt was left to resist the entire load. The mechanical advantage was further amplified by the lower position of the bottom bolt, and the final 50-pound pull on the guard rail became a 1,200-pound force at the base. This was enough to twist the stringer and cause it to crack longitudinally.  The tests were conducted on isolated posts without railing. Often, a continuous rail is used, which can help to distribute the load to other posts, decreasing the load effects on the bolts at a single post attachment. However, the test was designed for worst case scenarios, which were correctly reflected in the above testing.” Guardrail failure is unnecessary and the consequences can be tragic.

The new ICC-ES evaluated EZ Stairs® rail post attachment technology which affords a simple and efficient, code compliant solution to this very serious issue.

Look up report ICC-ESR 2295.

EZ Stairs® has been voted ‘Hot Product’ of the year at the International Builder’s Show over and over.  The system has won awards for innovation in the construction industry. It is the only adjustable bracket system anywhere and can be used to meet all building codes for any interior or exterior (deck stairs, wood stairs and concrete formwork stairs) application and can now double as a code compliant rail post support attachment ICC-ESR 2295. See a 3D video demo of how it works.

Build Safe Stair Railings with Closed Posts.

Build Safe Stair Railings with Closed Posts.

 

Build Safe Stair Railings for Open Post Stairs

Build Safe Stair Railings for Open Post Stairs

Free Stair Calculator

Free EZ Stair Calculator TM is now available online at EZ-Stairs.Com and offers a comprehensive approach to building stairs from stair project inception through project completion.

EZ Stairs®, a revolutionary advancement in stair building technology and construction, unveiled its new free  EZ Stair Calculator TM  available to the construction  marketplace.  The EZ Stair Calculator TM  is being made available with the goal of simplifying a normally difficult process, in addition to eliminating mistakes.  The entire process one goes through in using this new industry tool is quick and seamless, thereby eliminating frequent mistakes experienced in building stairs.  The result is faster construction, and eliminating unknowns such as material delays and excess costs due to streamline construction process afforded through the system.

This is an interactive and intuitive program designed to answer virtually every question a stair builder might have.  The program takes the builder, in a user friendly manner, through the process step by step (five steps total) and provides a print out option showing the finished stringer with cut dimensions and a materials list.  This new, ‘Free’ calculating tool allows Professionals and Do-It-Yourselfers to get up and running on their stair projects faster than ever before.  At conclusion, in the final step five, users are provided a print out option that shows a side view of the stringer, the stringer end details and cut dimensions, in addition to a full materials list for the entire project.

For the Decking Industry’s use of the EZ Stair Calculator TM, full calculations are made for either wood or composite stairs, including a variation on treads utilized and suggested manufacturers to use in the construction process.  Go to EZ Stairs to access the EZ Stair Calculator TM and the analysis and specifics given for each of your stair building projects.

The award winning EZ Stair® System features patented, adjustable parallel brackets that allow skilled carpenters as well as the do-it-yourselfer, to build stairs of superior strength and structural integrity up to four times faster than conventional methods.  Build stairs: deck stairs, interior stairs (basement stairs and tongue & groove), as well as concrete formwork. This adjustable two stringer stair building system is of particular value in the Decking Industry due to substantially lower costs that result in builders using this efficient, streamlined technique as part of their basic design.

EZ Stairs® has been ICC-ES approved for both residential and commercial construction. The full report is available at the EZ Stairs® website and can viewed online.   For more information, please call Gordon Walker, President, EZ Stairs®, Inc. (949-643-9261) or visit the website: www.ez-stairs.com.

EZ Stairs, Inc. • 27068 La Paz Rd. #263 • Aliso Viejo  CA 92656-3401 • 866-693-9570

Building Stairs on a Budget: deck stairs, basement stairs, interior stairs and concrete stairs

In this age of economic downturn, it is more important than ever to save every dime possible on your building projects. One of the most expensive areas of construction is found in stair building. There are several reasons.

First, stairs are often considered the exclusive domain of the “stair specialist”. Many people consider such a project to be well out of their range of expertise, and they reluctantly call in the “specialist”. Needless to say they are usually horrified at the high price, and often feel that they have no alternative but to either accept the bid or put the project on hold.

Secondly, stairs are usually more difficult than most construction projects because there are some very specific guidelines which are required by code, and if you get the initial planning wrong, you could be faced with tearing out and building the stairs again.

The standard or traditional methods of stair building have usually consisted of the marking out and freehand cutting of multiple stair stringers. Next, the stringers are attached and aligned and then the risers and treads are attached. This is a very cumbersome process which takes a great degree of skill and often, even the “specialist” gets it wrong.

The good news is, you can use an engineered stair building system, otherwise known as adjustable brackets. The benefits are that they’re much easier to install and only a very minimal skill level is necessary- compared to traditional framing. This system consists of adjustable stair brackets, that automatically adjust to the exact rise and run you require. The brackets are approved as joist hangers which allow the stair risers to be used structurally, carrying the load across the stair like floor joists. This kind of system is very strong and it has been tested for stairs up to nine feet wide, using only the two outside stringers. This completely eliminates the need for any interior stringers. The outside stringers then require only 3 to 4 cuts each, and the risers and treads are simply attached to the brackets. If you make a mistake, simply readjust the brackets. This kind of system is very versatile and can be used for deck stairs, basement stairs, any kind of interior stairs, as well as cement stairs.

Engineered adjustable stair brackets will  build finished interior stairs, basement stairs, deck and porch Stairs.

How will you save?

1. Little or no wasted wood because additional center stringers are eliminated  and only three to four end cuts are required for each of the outside stringer.

2. Since you only need two stringers, time is saved by eliminating the need to cut and align additional center stringers. No center stringers, means no squeaks.

3. The Brackets do the work by equally adjusting to give you the exact rise and run, eliminating costly mistakes and simplifying the whole process.

4. The system is so accurate that finished interior stairs can be built by installing finished risers and treads directly onto the brackets, eliminating traditional rough framing and up to 80% of the finished trim work normally required with traditional stair building methods.

5. Once the two stringers are built, the rest of the stair goes together like an erector set. A once very complicated job has been simplified to the point where a person with only basic skills can easily build a stronger, accurate stair and get it right the first time. See a 3D demo of how it works.

 How much can you save?

For interior finished stairs, the “stair specialist” can easily save up to $500.00 per flight because most of the traditional “custom trim work” is automatically eliminated. For most two story homes, that means $1000.00 savings. The DIY, the savings are obviously greater.

An approved “Engineered Stair System” eliminates the need to cut stringers and is tested to be much stronger and faster than conventional construction. Whether you’re a seasoned professional or a do-it-yourselfer, you will build fast, strong and accurate stairs, on a budget.

EZ Stairs® products allow builders to build stairs with a wide range of materials such as redwood, cedar, tropical wood, treated wood, untreated wood, vinyl, steel, and composites. This stair adjustable bracket building system allows for customized rise and treads configurations which can be adjusted to meet all building codes for any interior or exterior application- ICC approved. It is the only adjustable stair bracket system available anywhere. To help you figure out how many stairs you will need, the website provides a free stair calculator.

EZ Stairs® introduced the new patented adjustable dual-purpose exterior/interior brackets in 2003. In 2004, it won Pro Sales Magazine’s Editor’s Choice award for new product innovation in the construction industry. In 2005, it introduced its composite deck compatibility solution and was chosen for LBM Journal’s ‘Hot Products’ Award at the 2005 International Builders Show, and again voted one of the fifty ‘Hot Products’ at the 2008 International Builders Show.

For more information, visit the ez-stair.com website, or call 866-693-9570.

EZ Stairs® has been voted one of the ’50 Hot Products’ at the International Builder’s Show -several times. This stair adjustable bracket building system allows for customized rise and treads configurations which can be adjusted to meet all building codes for any interior or exterior application- ICC approved. It is It is the only adjustable stair bracket system available anywhere and can be used with a wide range of materials.
booth_panelpics_sm_extra_fl

Stair Building Innovations Make Easy to Install Staircase Construction

Building a staircase can be a daunting task for a do-it-yourselfer as well as a pro.  Traditional stair building methods are rigid and unforgiving. If you miscalculate or need to make adjustments, then you often have to throw out your materials and start over.  Luckily there are some new products and techniques on the market that can simplify and speed up stair construction.

One innovation that has many advantages compared to conventional stair building is the adjustable bracket method.  This technique differs from conventional stair construction with its ease of installation. With adjustable stair brackets such as EZ Stairs®, you can custom fit deck stairs into an exact area, forming any rise or run required.

Here are eight advantages of using adjustable brackets over traditional stair building methods:

1- Allows for a custom fit.

2- Ease of installation: 2 stringers, 3 saw cuts each

3- Less waste of materials.

4- No math skills required.

5- Simple adjustments correct errors.

6- Approved as joist hangers.

7- They provide ‘code compliant’ rail post support.

8. Big time savings in comparison.

This is how the adjustable bracket method works:

Step one: Set the brackets on the two 2×6 stringer members using the spacers and pivot screws.

Step two: Remove spacers and rotate brackets to adjust stair height.

Step three:Fix brackets in position, attach risers and treads. Before you begin, determine the exact number of steps you need and exactly how wide you would like your steps to span.

steps1_2_3amaz

For example, to make deck stairs up to seven feet wide using the automatic adjustable system, you only need three saw cuts per stringer and only two stringers are necessary. No center stringers are needed at all because riser acts as a load-bearing joist, spanning across the stair between the two stringers, giving you stronger stairs. Literally, in three steps you can build deck stairs. With the traditional method you must custom cut, align and support several stringers as needed for the stair width. This requires a high degree of skill.

There’s a lot less waste of wood too. With traditional stringers you cut away half the strength when forming the stair. Also, you don’t have the frustration with math and all the mistakes that come from mathematical error with the new building method. In most cases, a simple adjustment will eliminate the error. This will save you a lot of time. See what kinds of stair projects you can build.

Adjustable brackets not only adjust, but are also approved as ‘joist hangers’. This allows you to attach 2″ thick risers that span across the stair like floor joists, every 10″ or 11″ between the two stringers. This eliminates the need for several center stringers running down the stair as in conventional construction. Since there are only two stringers, you also eliminate the need to align and attach several cut stringers in order to build your stair.

Another benefit to using brackets is that they provide ‘code compliant’ rail post support. According to the accredited testing, the brackets are used to provide rail post support for any type of wood stair which meets the code requirement for 200lb. Lateral load at 42″. Conventional stair building doesn’t have a good solution for this rail post attachment problem. If a large person presses on the railing in traditional stair framing, it can easily give way.

So, for your next stair building project consider using the EZ Stairs adjustable bracket method.  It will save you time, materials, and a lot of unnecessary stress.

Building stairs that are easy to install.

Cut your labor in half with EZ Stairs’ adjustable brackets.

Welcome to the New EZ Stairs Blog and Website.

Latest EZ Stair News: Our adjustable stair brackets double as a rail post support, making strong stair railings that not only meet code but exceed it.

New Simple Solution for Stair Rail Safety: 15 Facts

                                            ICC-ESR # 2295 – Released January 2012

1.    Code requires all railing to hold 200 lb lateral load.

2.    This also applies to stair railing but in the past has not been enforced, since it was not possible to obtain            code compliant loads. New EZ Stairs® technology has now made code compliancy possible.

3.    Residential code requires 200 lb at 36” above the nose of the tread.

4.    Commercial code requires 200 lb at 42″ above the nose of the tread.

5.    The new EZ Stairs® R/P Support bracket is the first and only ICC/ES tested and accepted bracket which meets  code requirements for both residential and commercial wood stairs. ICC-ES Acceptance # ESR 2295 (January 2012)

6.    The EZ Stairs® bracket is designed to work equally well for all common stair types – cut stringers, stair angles, EZ Stairs® stacked stringers and housed or notched stringer types.

7.    EZ Stairs® brackets have been tested to exceed the 200 lb load requirements by a safety factor of 250%. This is equivalent to a lateral load of 500 lbs. at 42” (commercial).

8.    The EZ Stairs® brackets when tested at extreme measures, were subjected to a load in excess of 5,000 lbs.

9.    The strength of the EZ Stairs® bracket connection lies in the firm anchoring of the bracket flanges to the tread and blocking (at back of tread) or rise (at front of tread) – go to www.ez-stairs.com  for more information.

10.  EZ Stairs® introduces a simple and economical solution which meets all code requirements for both new construction and structural retrofits for existing rail posts.

11.  The National Safety Council (2011 Safety Statistics) reports that slips and falls are the leading cause of death for persons over age 65. The majority of these lethal injuries are falls from one level to another which includes fatalities and serious injuries on stairs.

12.  These documented statistics establish stairs as the most dangerous area of any deck, well in excess of the more widely and publicly discussed events such as deck collapse which claim relatively few lives when compared to the fatalities resulting from slips and falls on stairs.

13.  When anyone travels up or down a stair, proper safety precautions require a firm grip of the hand rail. If the rail is not properly secured and movement occurs, the ability to maintain a safe grip is compromised.

14.  Maintaining a safe, firm grip on stair railing, can reduce with age, therefore, it is essential to maintain rail post code requirements for rail stability. Failure to comply with set code requirements will increase builders & contractors potential risk of liability.

15.  It’s just a matter of time, as the construction industry is continually made more aware of real  areas of liability, that contractors will start to be exposed and vulnerable to litigation for failing to meet specific documented code requirements… specifically in the stair construction arena of lateral load stair rail safety.

How to build stairs with EZ Stairs
EZ Stairs brackets can also be used as rail post supports.

Build strong, code compliant rail post supports with EZ Stairs.